Sony SRS-D5100 Bedienungsanleitung PDF herunterladen

FRONT REAR CENTER/

WOOFER

VOLUME

BASS REAR CENTER

PHONE

OFF

POWER

OFF

Dual Stereo

MIN

MAX

 2004 Sony Corporation Printed in China

Operating Instructions

Manual de instrucciones

Active Speaker System

SRS-D5100

3-264-408-11(1)

POWER

VOLUME

Owner’s Record

The model number and the serial number are located on the rear of the

subwoofer.

Record the model number and the serial number in the space provided below.

Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. SRS-D5100

Serial No.

to wall outlet

“WALKMAN” is a registered

trademark of Sony Corporation to

represent Headphone Stereo products.

to Rear R jack

CD/MD Walkman*, etc

Line out of sound

card or sound box

• The unit is not disconnected from the AC power

source (mains) as long as it is connected to the wall

outlet, even if the unit itself has been turned off.

• Unplug the system from the wall outlet if it is not to

be used for an extended period of time. To disconnect

the cord, pull the cord by grasping the plug. Never

pull the cord itself.

• Should any liquid or solid object fall into the system,

unplug the system’s power cord and have the system

checked by qualified personnel before operating it

any further.

• The AC power cord should be changed only at a

qualified service shop.

• For efficient heat dissipation, ensure there is sufficient

space to the rear of the subwoofer. Also, avoid

placing objects on the unit.

• Do not insert your hand or any objects into the hole of

the subwoofer.

On operation

• Do not drive the speaker system with a continuous

wattage exceeding the maximum input power of the

system.

• Before connecting, turn off the speaker system, the

PC and audio component to avoid damaging the

speaker system.

• The volume level should not be turned up to the

point of distortion.

• Although this system is magnetically shielded, do not

leave recorded tapes, watches, personal credit cards

or floppy disks using magnetic coding in front of the

system for an extended period of time.

If the TV picture or monitor display is

magnetically distorted

Although this system is magnetically shielded, there may

be cases that the picture on some TV sets/personal

computers may become magnetically distorted. In such a

case, turn off the power of the TV set/personal computer

once, and after 15 to 30 minutes turn it on again. In the

case of a personal computer, take appropriate measures,

such as data storage, before turning it off.

When there seems to be no improvement, locate the

system farther away from the TV set/personal

computer. Furthermore, be sure not to place objects in

which magnets are attached or used near the TV set/

personal computer, such as audio racks, TV stands, toys

etc. These may cause magnetic distortion to the picture

due to their interaction with the system.

On placement

• Do not set the speakers in an inclined position.

• Do not leave the system in a location near heat

sources, or in a place subject to direct sunlight,

excessive dust, moisture, rain or mechanical shock.

• Do not install the satellite speaker anywhere other

than on a wall.

• Do not hang on the satellite speaker or hang anything

on it.

On cleaning

Do not use alcohol, benzene, or thinner to clean the

cabinet.

If you have any questions or problems concerning your

speaker system, please consult your nearest Sony

dealer.

to Front R jack

to Rear L jack

to Front L jack

to 8-pin Din jack

Subwoofer (rear)

Control Box

(rear)

to LINE OUT or

headphones jack

(stereo mini-jack)

PHONES

DUAL STEREO

Control box

This system needs either a sound card (5.1

channel) for PC or a decoder box. They are

not supplied with this system.

English

Before operating the unit, please read this manual

thoroughly and retain it for future reference.

WARNING

To prevent fire or shock hazard, do not expose the

unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer

servicing to qualified personnel only.

To prevent fire, do not cover the ventilation of the

apparatus with news papers, table-cloths, curtains, etc.

Do not place lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objects

filled with liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

CAUTION

You are cautioned that any changes or modification not

expressly approved in this manual could void your

authority to operate this equipment.

NOTICE FOR THE CUSTOMERS IN THE USA

This symbol is intended to alert the user to

the presence of uninsulated “dangerous

voltage” within the product’s enclosure

that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

This symbol is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Precautions

On safety

The nameplate indicating operating voltage, power

consumption, etc., is located on the rear exterior.

• Before operating the system, be sure that the

operating voltage of the system is identical with that

of your local power supply.

Where purchased Operating voltage

U.S.A./Canada 120 V AC, 60 Hz

European countries 220 – 230 V AC, 50 Hz

Other countries • 110 – 120 V AC, 50/60 Hz

• 220 – 230 V AC, 50 Hz

to INPUT2 jack

to LINE OUT jack (Green to

front, Orange to center, and

Black to rear channel)

Connecting Cable

(for 5.1 channel

signal input)

(supplied)

to INPUT1 jack (Green to front,

Orange to center, and Black to rear

channel)

to Center jack

Subwoofer (1) Control box (1) Connecting Cable (for 5.1

channel signal input) (1)

Satellite speaker (5) Base (5) Screw (5)

Satellite speaker

Base

Screw

Hollow wall anchors

(ø 4 mm, not supplied)

Anchor holes

Package Contents

PC, CD or MD

Walkman, etc.

Front speaker (Left)

Subwoofer

Control box

Front speaker (Right)

Rear speaker

(Right)

Center speaker

Installing the satellite speakers

(See fig. A)

Use the supplied screws to attach the base to the

satellite speaker. The satellite speaker can be used either

placed on a desk or attached to a wall.

When you use the satellite speaker on a desk

(See fig. A-A)

By attaching the base to the satellite speaker, it can be

placed on a desk.

1 Match the hole of the base and the

bottom hole of the satellite speaker.

Attach the base with the anchor holes facing

forward.

The base allows you to adjust the satellite speaker

to the desired angle.

2 Ensure the screws are tight.

Tighten the screw with your finger. If it is difficult,

use a screwdriver to secure the screw.

When you use the satellite speaker attached

to a wall (See fig. A-B)

By attaching the base to the satellite speaker, it can be

attached to a wall. Follow the Notes (below) to install

safely. Improper installation may result in the speaker

falling and causing bodily injury or damage to the

speaker or other object.

1 Align the hole in the base with the hole

at the rear of the satellite speaker.

Attach the base with the anchor holes uppermost.

The base allows you to adjust the satellite speaker

to the desired angle.

2 Ensure the screws are tight.

Tighten the screw with your finger. If it is difficult,

use a screwdriver to secure the screw.

3 Secure the hollow wall anchor in the wall

— refer to the illustration.

Notes

• Confirm wall thickness is sufficient. A

minimum thickness of 9.5 mm is recommended

for plasterboard.

• Use the specified clamp (hollow wall anchor,

not supplied) when attaching to plasterboard.

• Refer to the supplied operating instructions

using a hollow wall anchor.

• Use wall anchors of at least 20 kg hanging

capacity.

• Refer to the instruction supplied with hollow

wall anchor.

• Requires ø 4 mm hollow wall anchor.

• Set up the head of a hollow wall anchor 5 mm

from the wall.

• Apply a bond (anaerobic threadlocking

material) to the hollow wall anchor to prevent

the screw loosening.

4 Attach the satellite speaker to the wall.

Insert both wall anchors in the anchor holes of the

satellite speaker base.

Note

Ensure that the satellite speaker is securely

attached to the wall before use.

Hooking up the system

(See fig. B)

1 Connect the cord of the control box to

the 8-pin Din jack of the subwoofer with

their respective arrows aligned.

2 Connect the satellite speakers to the

subwoofer.

Confirm the location of the satellite speakers, and

then connect to their respective jacks.

3 Connect the control box to the source

equipment.

– Line out of sound card or sound box:

Connect the INPUT1 jacks (FRONT, REAR, and

CENTER/WOOFER) of the control box and the

jacks of the sound card with the supplied

connecting cord. For details, refer to the operating

instructions of the sound card.

– CD/MD Walkman, etc.:

Connect the INPUT2 jack of the control box and

LINE OUT or headphones jack of a CD/MD

Walkman, etc. The connecting cord is not supplied

with this system.

Note

To switch INPUT1 and INPUT2, use ON/OFF of

the device connected to the control box.

4 Connect the subwoofer to the wall

outlet.

5 Position the speakers. (See fig. C)

Listening to the sound (See fig. D)

First, turn down the volume on the control box. The

volume should be set to minimum before you begin

playing the programme source.

1 Set the POWER switch to ON on the

control box.

The POWER indicator lights up.

2 Adjust the VOLUME control on the

control box.

You can adjust the volume of the subwoofer and

each satellite speaker.

When connecting to the headphone output, also

adjust the volume of the connected component.

After listening, set the POWER switch to OFF.

The POWER indicator goes off.

3 Using headphones/earphones.

Connect headphones/earphones to the PHONES

jack on the control box.

Notes

• Turn off the MEGA BASS or BASS BOOST

(Walkman, etc.) function as it may cause audible

distortion.

• Only the front L/R channel signals will be

useful. You cannot use the BASS, REAR or

CENTER volume dial.

Rear speaker (Left)

40 mm

Troubleshooting

Should you encounter a problem with your speaker

system, check the following list and take the indicated

measures. If the problem persists, consult your nearest

Sony dealer.

There is no sound from the speaker system.

• Make sure all the connections have been correctly

made.

• Make sure the VOLUME dial and the each speaker’s

volume dial (BASS, REAR, CENTER) on the control

box.

• Make sure the connected component has been turned

up properly.

• Check if headphones are connected. If they are,

disconnect them.

The sound is distorted.

• Turn down the volume level on the connected

component. Or, if the connected component has a

BASS BOOST function, set it to off.

• Rotate BASS on this unit to reduce the bass volume.

• Turn VOLUME on this unit down to reduce the

volume.

There is hum or noise in the speaker output.

• Make sure all the connections have been correctly

made.

• Make sure none of the audio components are

positioned too close to the TV set.

The sound has suddenly stopped.

Make sure all the connections have been correctly made.

The brightness of the POWER indicator is

unstable.

The brightness of the POWER indicator may become

unstable when the volume is turned up. This is not a

malfunction.

Specifications

Speaker section

Satellite speaker

Speaker system Full range, magnetically shielded

Speaker units 5.6 cm, cone type

Enclosure type Closed type

Impedance 6 Ω

Cord length 3 m

Subwoofer

Speaker system Woofer

Speaker units 16 cm, cone type

Enclosure type Bass reflex

Impedance 6 Ω

Amplifier section

Rated output 12 W (10% T.H.D., 1 kHz, 6 Ω)

(Satellite speaker)

80 W (10% T.H.D., 100 Hz, 6 Ω)

(Subwoofer)

Input Stereo mini jack × 3 (INPUT 1 for 5.1

channel signal input)

Stereo mini jack × 1 (INPUT 2 for 2

channel signal input)

Input impedance 4.7 kΩ (at 1 kHz)

Output Stereo mini jack × 1 (PHONES)

General

Dimensions (w/h/d) Approx. 166 × 40 × 83 mm

/8 × 1

/8 × 3

/8 in.) (Control box)

Approx. 95 × 135 × 150 mm

/4 × 5

/8 × 6 in.) (Satellite speaker,

on a desk)

Approx. 95 × 100 × 180 mm

/4 × 4 × 7

/8 in.) (Satellite speaker,

attached to a wall)

Approx. 285 × 285 × 462 mm

(11

/4 × 11

/4 × 18

/4 in.)

(Subwoofer)

Mass Approx. 240 g (8 oz.) (Control box)

Approx. 490 g (1 lb. 1 oz.)

(Satellite speaker)

Approx. 8.7 kg (19 lb. 3 oz.)

(Subwoofer)

Cord length 2 m (Control box to subwoofer)

2 m (Power cord)

Power consumptions 42 W

Supplied accessories

Connecting Cable (for 5.1 channel signal input)

Optional accessories

Connecting cord RK-G136, RK-G138

Plug adaptor PC-236MS

Design and specifications are subject to change without

notice.

Attach the base with the

anchor holes facing forward

The speaker angle can

be changed by

attaching the base

back to front.

Attach the base with the

anchor holes uppermost

Note

First, be sure to apply a bond (anaerobic

threadlocking material) to the hollow wall

anchor to prevent the screw loosening.

9.5 mm or more

ø 4 mm

5 mm

7 mm

Note

Do not hang on the satellite speaker or hang

anything on it.

Connecting cord

(not supplied)

Satellite speaker

(rear)

VOLUME: Controls total volume level.

BASS: Adjusts bass level (Subwoofer)

REAR: Adjusts rear surround sound (Rear Speaker)

CENTER: Adjusts center speaker level as necessary to

make balanced sound

PHONE: Connect to headphones for personal listening

In this case, only the front L/R channel signals will

be useful. The CENTER channel is not activated. You

cannot use the BASS, REAR or CENTER volume dial.

DUAL STEREO: Switches a 4 channel or 2 channel

source to 5.1 channel.

Set the switch to ON when a 4-channel or 2-channel

source is output from a PC, Walkman, etc., connected

to this system. The front and rear speakers will be

output the front channel of these sources. The center

speaker will be output the mixed left and right front

channels of these sources. In this case, the subwoofer,

center and rear speakers will not operate with a 5.1-

channel source.

Set the switch to OFF when a 5.1-channel source is

output from a PC or sound card connected to this

system. 5.1-channel surround sound will be output.

In this case, the subwoofer rear and center speakers

will not operate with a 2-channel source, and the

center speaker and subwoofer will not operate with a

4-channel source. For details about the sound card

setting, refer to the operating instructions of the

sound card.

1 2

Inhaltsverzeichnis

Seite 1 - Active Speaker System

FRONT REAR CENTER/WOOFERVOLUMEBASS REAR CENTERPHONEONOFFPOWERONOFFDual StereoMINMAXB 2004 Sony Corporation Printed in ChinaOperating Instru

Seite 2 - ADVERTENCIA

Este sistema requiere una tarjeta de sonido(5.1 canales) para PC o un decodificador, queno se suministran con el sistema. EspañolAntes de utilizar la

Kommentare zu diesen Handbüchern

Keine Kommentare

Sony SRS-D5100 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio Sony SRS-D5100 herunter. Sony SRS-D5100 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio Sony SRS-D5100