Sony MDR-RF855RK Bedienungsanleitung PDF herunterladen

Wireless Stereo

Headphone System

4-441-668-15(1)

MDR-RF855RK

English Wireless Stereo Headphone System

WARNING

To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

To reduce the risk of fire or electric shock, do not expose this

apparatus to dripping or splashing, and do not place objects

filled with liquids, such as vases, on the apparatus.

Do not expose the batteries (battery pack or batteries installed)

to excessive heat such as sunshine, fire or the like for a long time.

Do not dismantle, open or shred secondary cells or batteries.

In the event of a cell leaking, do not allow the liquid to come in

contact with the skin or eyes. If contact has been made, wash the

affected area with copious amounts of water and seek medical

advice.

Secondary cells and batteries need to be charged before use.

Always use the correct charger and refer to the manufacturer’s

instructions or equipment manual for proper charging

instructions.

After extended periods of storage, it may be necessary to charge

and discharge the cells or batteries several times to obtain

maximum performance.

Dispose of properly.

To avoid electrical shock, do not open the cabinet. Refer

servicing to qualified personnel only.

Do not install the appliance in a confined space, such as a

bookcase or built-in cabinet.

As the main plug of AC power adaptor is used to disconnect the

AC power adaptor from the mains, connect it to an easily

accessible AC outlet. Should you notice an abnormality in it,

disconnect it from the AC outlet immediately.

Excessive sound pressure from earphones and headphones can

cause hearing loss.

The nameplate of transmitter is located on the bottom exterior.

The validity of the CE marking is restricted to only those

countries where it is legally enforced, mainly in the countries EEA

(European Economic Area).

Hereby, Sony Corporation declares that this equipment is in

compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at

the following internet address:

http://www.compliance.sony.de/

Disposal of Old Electrical & Electronic

Equipment (Applicable in the European

Union and other European countries with

separate collection systems)

This symbol on the product or on its packaging

indicates that this product shall not be treated

as household waste. Instead it shall be handed

over to the applicable collection point for the recycling of

electrical and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of

this product. The recycling of materials will help to conserve

natural resources. For more detailed information about recycling

of this product, please contact your local Civic Office, your

household waste disposal service or the shop where you

purchased the product.

Disposal of waste batteries (applicable in

the European Union and other European

countries with separate collection systems)

This symbol on the battery or on the packaging

indicates that the battery provided with this

product shall not be treated as household waste.

On certain batteries this symbol might be used in combination

with a chemical symbol. The chemical symbols for mercury (Hg)

or lead (Pb) are added if the battery contains more than 0.0005%

mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will

help prevent potentially negative consequences for the

environment and human health which could otherwise be

caused by inappropriate waste handling of the battery. The

recycling of the materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity

reasons require a permanent connection with an incorporated

battery, this battery should be replaced by qualified service staff

only.

To ensure that the battery will be treated properly, hand over the

product at end-of-life to the applicable collection point for the

recycling of electrical and electronic equipment.

For all other batteries, please view the section on how to remove

the battery from the product safely. Hand the battery over to the

applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or

battery, please contact your local Civic Office, your household

waste disposal service or the shop where you purchased the

product.

Notice for customers: the following information is only

applicable to equipment sold in countries applying EU

directives

This product has been manufactured by or on behalf of Sony

Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan.

Inquiries related to product compliance based on European

Union legislation shall be addressed to the authorized

representative, Sony Belgium, bijkantoor van Sony Europe

Limited, Da Vincilaan 7-D1, 1935 Zaventem, Belgium. For any

service or guarantee matters, please refer to the addresses

provided in the separate service or guarantee documents.

How to use

After use

The headphones automatically turn off when they are taken

off (Auto power on/off function).

About auto power on/off function

When you put on the headphones, the headphones' power

turns on automatically. Wear the headphones vertically on

your head so that auto power on function is properly

activated.

The headphones automatically turn off when they are taken

off.

Do not pull up the self-adjusting band when not in use, this

will consume the battery power.

Self-adjusting band

About sending RF signals

The transmitter starts sending RF signals automatically when

it detects an audio signal from the connected component.

Note that;

Noise may occur depending on the transmitter position and

room conditions. It is recommended to place the

transmitter in a location that produces the clearest sound.

If the transmitter is placed on a metallic table, you may hear

noise, or the reception range may decrease. Do not place on

a metallic table.

If low signal or no signal is input for

about 5 minutes

If low signal is input for about 5 minutes, the transmitter turns

off automatically*. If the volume of the connected A/V

component is too low, the transmitter may also turn off. When

low signal is input, the POWER/GREEN indicator of the

transmitter flashes green for 5 minutes, then turns off. In this

case, raise the volume of the connected A/V component

within the range where the sound is not distorted, then lower

the volume of the headphones.

The transmitter may also turn off if no signal is input for about

5 minutes. The POWER/GREEN indicator of the transmitter

flashes green for 5 minutes, then turns off. The transmitter

restarts after receiving an audio signal again.

* If signal noise is output from the connected A/V

component, the transmitter may not turn off, even when no

audio signal is input.

–

Tips for charging

Charge supplied battery first

The supplied rechargeable nickel-metal hydride battery is not

charged from the first time you use it. Be sure to charge them

before use.

About auto charge function

Placing the headphones on the transmitter automatically turns

them off, then charging starts. This eliminates the need for

turning on/off every time you wear and take off the headphones.

If CHG/RED indicator does not light up

red

Check if the right and left headphones are rested on the

transmitter correctly. Take off the headphones and place them

on the transmitter again so that the headphones’ contact

points meet the transmitter’s contact pins.

Charging may not be completed if the transmitter’s contact

pin and headphones’ contact point are dusty. Wipe them with

a cotton bud, etc.

Charging and usage time

Depending on the remaining battery status, it takes approx. 30

minutes to 7 hours to recharge.

Approx. charging time Approx. usage time

7 hours

18 hours

1) at 1 kHz, 0.1 mW + 0.1 mW output

2) hours required to fully charge an empty battery

3) Time may vary, depending on the temperature or conditions

of use.

To recharge supplied battery after use

Place the headphones on the transmitter after use. The CHG/RED

indicator lights up red, then charging starts.

When charging is complete, there is no need to remove the

headphones from the transmitter.

Remaining battery

To check the remaining battery charge of the headphones, pull

up the self-adjusting band, and check the POWER indicator. The

battery is still serviceable when the indicator lights up green.

Charge the headphones if the POWER indicator turns off, dims,

flashes, or the sound becomes distorted or noisy.

Notes

Insert the AC adaptor plug firmly.

Be sure to use the supplied AC adaptor. Using AC adaptors

with different plug polarity or other characteristics can cause

product failure.

Unified

polarity plug

The battery capacity may decrease if the headphones are

turned on and placed on the transmitter with the AC adaptor

disconnected.

The transmitter automatically turns off while charging the

battery.

This system is designed to charge only the supplied

rechargeable battery BP-HP550-11 for safety. Note that other

types of rechargeable battery cannot be charged with this

system.

If dry batteries are installed, they cannot be charged.

Do not attempt to use the supplied rechargeable battery BP-

HP550-11 for other components. It is for use with this system

only.

Charge in an environmental temperature of between 5 °C and

35 °C (between 41 °F and 95 °F).

When the battery life reduces to half, this may be the end of

battery lifetime. The supplied rechargeable battery BP-HP550-

11 is not commercially available. You can order the battery

from the store where you purchased this system, or at your

nearest Sony dealer.

–

Using the headphones

with separately-sold dry

batteries

Commercially available (LR03 (size AAA)) dry batteries can also

be used to power the headphones. Install two batteries in the

same manner as described in step 1 of “How to use.”

When dry batteries are installed, the battery charge function is

not activated.

Battery life

Battery Approx. usage time

Sony alkaline battery LR03

(size AAA)

28 hours

1) at 1 kHz, 0.1 mW + 0.1 mW output

2) Time may vary, depending on the temperature or conditions

of use.

Note

Do not carry a dry battery together with coins or other metallic

objects. It can generate heat if the positive and negative

terminals of the battery are accidentally come into contact with

metallic objects.

Tips for connection

Do not connect to the AUDIO IN 1 and AUDIO IN 2 jacks at the

same time. If you connect two A/V components to both jacks

at the same time, both of the audio signals may result in mixed

output.

When you connect the connecting cable directly to an

earphone jack (monaural mini jack), the audio signal may not

be output through the right channel.

Tips for volume setting

If you connect the transmitter to the headphone jack of the A/

V component, set the volume of the A/V component as high as

possible but not so high that the audio signal becomes

distorted.

When watching videos, be careful not to raise the volume too

high in quiet scenes. You may hurt your ears when a loud

scene is played.

Tips for better reception

Receiving performance

This system utilizes very high frequency signals in the 800 MHz

band so the receiving performance may deteriorate due to the

surroundings. The following examples illustrate conditions that

may reduce the reception range or cause interference.

Inside a building with walls containing steel beams

An area with many steel file cabinets, etc.

An area with many electrical appliances capable of generating

electromagnetic fields

The transmitter is placed on a metal instrument.

An area facing a roadway

Noise or interfering signals exist in the surroundings due to

radio transceivers in trucks, etc.

Noise or interfering signals exist in the surroundings owing to

wireless communication systems installed along roadways.

Effective area of the transmitter

The optimum distance is up to approximately 100 m without the

system picking up some interference. However, the distance may

vary depending on the surroundings and environment.

If the system picks up some noise within the above mentioned

distance, reduce the distance between the transmitter and the

headphones, or select another channel.

When you use the headphones inside the effective area of the

transmitter, the transmitter can be placed in any direction from

the listener.

Even within the signal reception area, there are some spots

(dead spots) where the RF signal cannot be received. This

characteristic is inherent to RF signals, and does not indicate

malfunction. By slightly moving the transmitter, location of the

dead spot can be changed.

Replacing the earpads

The earpads are replaceable. If the earpads become dirty or

worn out, replace them as illustrated below. The earpads are not

commercially available. You can order replacements from the

store where you purchased this system, or at your nearest Sony

dealer.

1 Remove the old earpad by pulling it out of the groove on the

housing.

2 Place the new earpad on the driver unit.

Hang the edge of the earpad on one side of the driver unit’s

groove edge, then turn the edge of earpad around the driver

unit as illustrated below.

When the earpad is securely inserted into the groove, adjust

the earpad to the vertical position.

Troubleshooting

If you run into any problems using this system, use the following

checklist. Should any problem persist, consult your nearest Sony

dealer.

No sound/Low sound

Check the connection of the A/V component or the AC

adaptor.

Check that the A/V component is turned on.

If you connect the transmitter to an A/V component using the

headphone jack, raise the volume level on the connected A/V

component within the range where the sound is not distorted.

–

Change the radio frequency with the CHANNEL selector on the

transmitter, then change the radio frequency to that of the

transmitter with the TUNING switch on the headphones.

Use the headphones near the transmitter, or change the

position of the transmitter.

Charge the supplied rechargeable battery, or replace dry

batteries with new ones. If the POWER indicator is still off after

charging, take the headphones to a Sony dealer.

Raise the headphone volume.

Distorted or intermittent sound

(sometimes with noise)

Use the headphones near the transmitter, or change the

position of the transmitter.

Do not place the transmitter on a metallic table.

If you connect the transmitter to an A/V component using the

headphone jack, lower the volume level on the connected A/V

component within the range where the sound is not distorted.

Change the radio frequency with the CHANNEL selector on the

transmitter, then change the radio frequency to that of the

transmitter with the TUNING switch on the headphones.

Charge the supplied rechargeable battery, or replace dry

batteries with new ones. If the POWER indicator is still off after

charging, take the headphones to a Sony dealer.

Loud background noise

If you connect the transmitter to an A/V component using the

headphone jack, raise the volume level on the connected A/V

component within the range where the sound is not distorted.

Charge the supplied rechargeable battery, or replace dry

batteries with new ones. If the POWER indicator is still off after

charging, take the headphones to a Sony dealer.

Do not place the transmitter on a metallic table.

Use the headphones near the transmitter.

The POWER/GREEN indicator flashes

green

No signal or low signal is input. Start playback of the A/V

component, or raise the volume of the connected A/V

component within the range where the sound is not distorted,

otherwise the transmitter will turn off. If no signal or low signal

is input for about 5 minutes, the transmitter turns off

automatically.

The sound cuts off

The transmitter turns off if no signal or low signal is input for

5 minutes. If you connect the transmitter to an A/V component

using the headphone jack, raise the volume level on the

connected A/V component within the range where the sound

is not distorted.

Battery cannot be charged/

CHG/RED indicator flashes red, or does

not light up red

Check that the right/left of the headphones and transmitter

correspond, and put the headphones on the transmitter

correctly.

Install the supplied rechargeable nickel-metal hydride battery.

Dry batteries and rechargeable batteries other than the

supplied cannot be charged.

If the CHG/RED indicator does not light up red even though

you put the headphones on the transmitter and wait for a

while, it may be the end of battery lifetime. You can order the

supplied rechargeable battery BP-HP550-11 from the store

where you purchased this system, or at your nearest Sony

dealer.

Charging may not be completed if the transmitter’s contact

pin and headphones’ contact point are dusty. Wipe them with

a cotton bud, etc.

Precautions

When this system is not to be used for a long period of time,

disconnect the AC adaptor from the AC outlet holding the

plug, and remove the battery from the headphones to avoid

damage caused by battery leakage and subsequent corrosion.

Do not leave this system in a location subject to direct

sunlight, heat or moisture.

You may hear some noise when you disconnect the AC

adaptor from the transmitter before taking off the

headphones.

Avoid exposure to temperature extremes, direct sunlight,

moisture, sand, dust or mechanical shock.

Notes on headphones

To reduce the risk of hearing damage

Avoid using headphones at high volume. Hearing experts advise

against continuous, loud and extended play. If you experience a

ringing in your ears, lower the volume or discontinue use.

Caring for others

Keep the volume at a moderate level. This will allow you to hear

outside sounds and to be considerate to the people around you.

If you have any questions or problems concerning the system

that are not covered in this manual, please consult your nearest

Sony dealer.

Be sure to bring the headphones and the transmitter to the Sony

dealer when requiring repair work.

Specifications

RF stereo transmitter (TMR-RF855R)

Modulation FM stereo

Operating frequency

863.0 MHz – 865.0 MHz

Maximum output power

< 10 mW

Channel Ch1, Ch2, Ch3

Transmission distance

Approx. 100 m of longest

Audio inputs Pin jacks (left/right)

Stereo mini jack

Power requirements

DC 12 V (from the supplied AC adaptor)

Dimensions Approx. 180 mm × 94 mm × 126 mm (w/h/d)

Mass Approx. 310 g

Rated power consumption

3.0 W

Operating temperature

5°C to 35°C (41°F to 95°F)

Wireless stereo headphones (MDR-RF855R)

Frequency response

10 Hz – 22,000 Hz

Power source Supplied rechargeable nickel-metal hydride

battery BP-HP550-11, or commercially

available (LR03 (size AAA)) dry batteries

Mass Approx. 280 g including battery

Operating temperature

5°C to 35°C (41°F to 95°F)

–

Connect the AC adaptor.

Insert the plug firmly.

Charge the headphones.

To AC

outlet

(Red) (Off)

Complete when

indicator turns off.

Connect the A/V component, following hookup  or  below.

Insert the plug firmly.

 Using the headphone jack of the A/V component

L (white)R (red)

Stereo mini plug

Headphone jack

(Stereo mini jack)

TV, Digital music player, etc.

L (white)

R (red)

Stereo mini plug

Audio out

(L/R) jacks

Stereo system, Blu-ray Disc player,

DVD player, etc.

Start playback of the A/V component.

The POWER/GREEN indicator of the transmitter lights up green.

Wear the headphones.

Before listening

To reduce the risk of hearing damage, first lower the volume.

 Using the audio out (L/R) jacks of the A/V component

Insert the supplied rechargeable battery BP-HP550-11 into the left housing of the headphones.

Observe the correct polarity when installing battery.

Contact

pins

Rechargeable nickel-metal hydride

battery BP-HP550-11 (supplied)

Contact

points

Tactile dot

Insert the 

end first.

Operating Instructions

Mode d’emploi

Checking the included

items

Transmitter TMR-RF855R (1)

AC adaptor (1)

Rechargeable nickel-metal

hydride battery

(BP-HP550-11) (1)

Headphones MDR-RF855R (1)

Connecting cable (stereo mini

plug  pin plug × 2), 1 m (1)

Features

Thank you for purchasing the Sony MDR-RF855RK Wireless

Stereo Headphone System. Before operating the unit, please

read this manual thoroughly and retain it for future reference.

Some features are:

Wireless headphone system with long battery life and 100 m

range

Hassle-free recharging by placing the headphones on the

transmitter

40 mm driver units for deep bass response

Auto power on/off function for longer battery life

Battery playback time up to 18 hrs with rechargeable batteries

or 28 hrs with Sony alkaline batteries

–

Lock Release

Adjust the volume.

Down

Tactile dot

If you cannot receive a clear audio signal

First change the radio frequency with the CHANNEL selector switch on the transmitter,

then change the radio frequency to that of the transmitter with the TUNING switch on

the headphones.

(Green)

Svenska

Härmed försäkrar Sony Corporation att denna utrustning

överensstämmer med direktiv 2014/53/EU.

Den fullständiga texten till EU-försäkran om överensstämmelse

finns på följande webbadress:

http://www.compliance.sony.de/

Dansk

Herved erklærer Sony Corporation, at dette udstyr er i

overensstemmelse med direktiv 2014/53 / EU.

Den fulde ordlyd af EU-overensstemmelseserklæringen er

tilgængelig på følgende internetadresse:

http://www.compliance.sony.de/

Suomi

Sony Corporation vakuuttaa, että tämä laite on direktiivin

2014/53/EU mukainen.

EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on

saatavilla seuraavassa internetosoitteessa:

http://www.compliance.sony.de/

Norsk

Herved erklærer Sony Corporation at utstyrstypen er i samsvar

med direktiv 2014/53/EU.

EU-erklæring fulltekst finner du på Internett under:

http://www.compliance.sony.de/

Français

Le soussigné, Sony Corporation, déclare que cet équipement est

conforme à la Directive 2014/53/UE.

Le texte complet de la déclaration UE de conformité est

disponible à l’adresse internet suivante :

http://www.compliance.sony.de/

Deutsch

Hiermit erklärt Sony Corporation, dass diese Funkanlage der

Richtlinie 2014/53/EU entspricht.

Der vollständige Text der EU-Konformitätserklärung ist unter der

folgenden Internetadresse verfügbar:

http://www.compliance.sony.de/

Español

Por la presente, Sony Corporation declara que este equipo es

conforme con la Directiva 2014/53/UE.

El texto completo de la declaración UE de conformidad está

disponible en la dirección Internet siguiente:

http://www.compliance.sony.de/

Nederlands

Hierbij verklaart Sony Corporation dat deze radioapparatuur

conform is met Richtlijn 2014/53/EU.

De volledige tekst van de EU-conformiteitsverklaring kan

worden geraadpleegd op het volgende internetadres:

http://www.compliance.sony.de/

Italiano

Con la presente, Sony Corporation dichiara che questo

apparecchio è conforme alla Direttiva 2014/53/UE.

Il testo completo della dichiarazione di conformità UE è

disponibile al seguente indirizzo Internet:

http://www.compliance.sony.de/

Português

O(a) abaixo assinado(a) Sony Corporation declara que o presente

equipamento está em conformidade com a Diretiva 2014/53/UE.

O texto integral da declaração de conformidade está disponível

no seguinte endereço de Internet:

http://www.compliance.sony.de/

Slovensky

Sony Corporation týmto vyhlasuje, že zariadenie je v súlade so

smernicou 2014/53/EÚ.

Úplné vyhlásenie EÚ o zhode je k dispozícii na tejto internetovej

adrese:

http://www.compliance.sony.de/

Slovenščina

Sony Corporation potrjuje, da je ta oprema skladna z Direktivo

2014/53/EU.

Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem

spletnem naslovu:

http://www.compliance.sony.de/

Česky

Sony Corporation tímto prohlašuje, že toto zařízení je v souladu

se směrnicí 2014/53/EU.

Úplné znění EU prohlášení o shodě je k dispozici na této

internetové adrese:

http://www.compliance.sony.de/

Magyar

A Sony Corporation igazolja, hogy ez a készülék megfelel a

2014/53/EU irányelvnek.

Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a

következő internetes címen:

http://www.compliance.sony.de/

Български

С настоящото, Sony Corporation декларира, че това

оборудване е в съответствие с Директива 2014/53/EU.

Цялостният текст на ЕС декларацията за съответствие може

да се намери на следния интернет адрес:

http://www.compliance.sony.de/

Polski

Sony Corporation niniejszym oświadcza, że to urządzenie jest

zgodne z dyrektywą 2014/53/UE.

Pełny tekst deklaracji zgodności UE jest dostępny pod

następującym adresem internetowym:

http://www.compliance.sony.de/

Română

Prin prezenta, Sony Corporation declară că acest echipament

este în conformitate cu Directiva 2014/53/UE.

Textul integral al declarației UE de conformitate este disponibil la

următoarea adresă internet:

http://www.compliance.sony.de/

Included items

RF stereo transmitter TMR-RF855R

Wireless stereo headphones MDR-RF855R

AC adaptor (12 V) (1)

Connecting cable (stereo mini plug  pin plug × 2), 1 m (1)

Rechargeable nickel-metal hydride battery BP-HP550-11

(550 mAh min) (1)

Card warranty (1)

Operating Instructions (this manual) (1)

Design and specifications are subject to change without notice.

1 2

Wireless Stereo 1
Headphone System 1

Inhaltsverzeichnis

Seite 1 - Headphone System

Seite 2

Wireless Stereo Headphone SystemMDR-RF855RKFrançais Système de casque d’écoute stéréo sans filAVERTISSEMENTPour réduire les risques d’incendie ou d’él

Kommentare zu diesen Handbüchern

Keine Kommentare

Sony MDR-RF855RK Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Kopfhörer Sony MDR-RF855RK herunter. Sony MDR-RF855RK Operating Instructions Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kopfhörer Sony MDR-RF855RK