©2009 Sony Corporation4-129-783-11(3)Multi Channel AV ReceiverOperating InstructionsSTR-DH700
10USName FunctionE DTS(-ES) indicators DTS DTS-ES DTS 96/24Light up when DTS or DTS-ES signals are input.Lights up when the receiver is decoding DT
100USOn placement• Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver.• Do not pl
101US Additional InformationTroubleshootingIf you experience any of the following difficulties while using the receiver, use this troubleshoot
102USThere is severe hum or noise.• Check that the speakers and components are connected securely.• Check that the connecting cords are away from a tr
103US Additional InformationThere is no picture or an unclear picture appears on the TV screen.• Select the appropriate input using the input
104USThe TV’s remote cannot be used to control the connected component when using the Control for HDMI function.• Change the input of the receiver to
105US Additional InformationThe FM reception is poor.• Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM ante
106USClearing the receiver’s memory may remedy the problem (page 29). However, note that all memorized settings will be reset to their initial setting
107US Additional InformationInputsAnalog Sensitivity: 500 mV/ 50 kohms S/N3): 96 dB (A, 500 mV4))Digital (Coaxial) Impedance: 75 ohms S/N: 100
Sony Corporation Printed in MalaysiaIndexNumerics2 channel 602CH STEREO 605.1 channel 177.1 channel 17AAUTO CALIBRATION 31AUTO FORMAT DIRECT (A
11USName FunctionM Playback channel indicators L R C SL SR S SBL SBR SBThe letters (L, C, R, etc.) indicate the channels being played back. The
12USRear panel5668 712 3 4LRDIGITAL(ASSIGNABLE)DC5V0.7A MAXHDMIANTENNADMPORTSIRIUSSAT INSATINDVD IN BD IN OUTAMCENTER SURROUNDFRONT ALLRR LRYPB/CBCOMP
13US* You can watch the selected input image when you connect the MONITOR OUT or HDMI OUT jack to a TV or projector (page 20).You can use the supplied
14USName FunctionA TV ?/1 (on/standby)Press TV ?/1 and TV (M) at the same time to turn the TV on or off.AV ?/1 (on/standby)Press to turn on or off th
15USName FunctionHa)b)Press to start playback of the VCR, CD player, DVD player, or Blu-ray disc player.Xb)Press to pause playback or recording of the
16USa)The number 5, MASTER VOL +, TV VOL +, and H buttons have tactile dots. Use the tactile dots as references when operating the receiver.b)This but
17USGetting Started1: Installing the speakersThis receiver allows you to use a 7.1 channel system (7 speakers and one subwoofer).To fully enjoy theate
18US2: Connecting the speakersBefore connecting the cords, be sure to disconnect the AC power cord (mains lead).AFront speaker A (left)BFront speaker
19USGetting Starteda)If you connect only one surround back speaker, connect it to the SPEAKERS SURROUND BACK/BI-AMP/FRONT B L terminals.b)If you are n
2USTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.To reduce the risk of fire, do not cover the ventila
20US3: Connecting the TVYou can watch the selected input image when you connect the HDMI OUT or MONITOR OUT jack to a TV.It is not necessary to connec
21USGetting StartedNotes• Be sure to turn on the receiver when the video and audio signals of a playback component are being output to a TV via the re
22US4b: Connecting the video componentsThis section describes how to connect your video components to this receiver. Before you begin, refer to “Compo
23USGetting StartedHDMI is the abbreviated name for High-Definition Multimedia Interface. It is an interface which transmits video and audio signals i
24USHDMI features• A digital audio signal transmitted by HDMI can be output from the speakers connected to this receiver. This signal supports Dolby D
25USGetting StartedThe following illustration shows how to connect a DVD player or a Blu-ray disc player.It is not necessary to connect all the cords.
26USThe following illustration shows how to connect a satellite tuner or a set-top box.It is not necessary to connect all the cords. Connect audio and
27USGetting StartedThe following illustration shows how to connect a component which has analog jacks such as a DVD recorder, VCR, etc.It is not neces
28USNotes• Be sure to change the factory setting of the VIDEO 1 input button on the remote so that you can use the button to control your DVD recorde
29USGetting Started6: Preparing the receiver and the remoteConnect the AC power cord (mains lead) to a wall outlet.Before using the receiver for the f
3US12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use cau
30USInsert two R6 (size-AA) batteries in the RM-AAU021 Remote Commander.Observe the correct polarity when installing batteries.Notes• Do not leave th
31USGetting Started8: Calibrating the appropriate settings automatically (AUTO CALIBRATION)The DCAC (Digital Cinema Auto Calibration) function allows
32US1 Press AMP MENU.2 Press AUTO CAL.Measurement starts in 5 seconds and the display changes as follows:A.CAL [5] t A.CAL [4] t A.CAL [3] t A.CAL [2]
33USGetting StartedTips• When Auto Calibration starts:– Stand some distance from the speakers and the listening position to avoid measurement failure.
34USTo change the settings manually1 Record down the warning code.2 Press .3 Press ?/1 to turn off the receiver.4 Follow the solution provided in the
35USGetting Started9: Adjusting the speaker levels and balance (TEST TONE)You can adjust the speaker levels and balance while listening to the test to
36USSelecting a component1Press the input button to select a component.You can also use INPUT SELECTOR on the receiver.The selected input appears on t
37US PlaybackYou can enter a name of up to 8 characters for inputs and display it on the receiver’s display.This is convenient for labeling the jacks
38USListening/Watching a componentListening to a Super Audio CD/CD12346780/10ENTER9SYSTEM STANDBYTV INPUTSLEEPDMPORTVIDEO1 VIDEO2 BD DVD2CH A.F.D.TV C
39US PlaybackWatching a DVD/Blu-ray disc12346780/10ENTER9SYSTEM STANDBYTV INPUTSLEEPDMPORTVIDEO1 VIDEO2 BD DVD2CH A.F.D.TV CH –PRESET –TV CH +PRESET +
4USAbout This Manual• The instructions in this manual are for model STR-DH700. Check your model number by looking at the lower right corner of the fr
40USNavigating through menusBy using the amplifier menus, you can make various adjustments to customize the receiver.1 Press AMP MENU.“1-LEVEL” appear
41US Amplifier OperationsThe following options are available in each menu. For details on navigating through menus, see page 40.Overview of the menus
42USMenu [Display]Parameters [Display]Settings Initial settingTUNER [4-TUNER] (page 48)FM station receiving modea) [FM MODE]FM AUTO, FM MONO FM AUTON
43US Amplifier OperationsMenu [Display]Parameters [Display]Settings Initial settingSYSTEM [7-SYSTEM] (page 51)Subwoofera) [SW SPK]NO, YES YESFront sp
44USa)For details, refer to the page in the parentheses.b)You can only select this parameter when the surround back speakers are set to “SINGLE”.c)You
45US Amplifier OperationsAdjusting the level (LEVEL menu)You can use the LEVEL menu to adjust the balance and level of each speaker. These settings a
46USAdjusting the equalizer (EQ menu)You can use the EQ menu to adjust the tonal quality (bass/treble level) of the front speakers. Select “2-EQ” in t
47US Amplifier OperationsBy decoding the surround back signal of DVD software (etc.) recorded in Dolby Digital Surround EX, DTS-ES Matrix, DTS-ES Dis
48USNotes• There may be no sound from the surround back speaker in Dolby Digital EX mode. Some discs have no Dolby Digital Surround EX flag even thoug
49US Amplifier Operationsx SR ID (SIRIUS radio ID)Lets you check the SIRIUS Radio ID. For details, see “Checking the SIRIUS Radio ID” (page 67).Setti
5USTable of ContentsDescription and location of parts ... 7Getting Started1: Installing the speakers... 172:
50USx DUAL (Digital broadcast language selection)Lets you select the language you want to listen to during digital broadcast. This feature only functi
51US Amplifier Operationsx CONTROL FOR HDMI (Control for HDMI)Lets you turn the Control for HDMI function on or off. For details, see ““BRAVIA” Sync
52USx CNT SPK (Center speaker)• NO If you have not connected a center speaker, select “NO”. The sound of the center channel will be output from the fr
53US Amplifier Operationsx SB ASGN (Surround back speaker assign)•OFFIf you connect surround back speakers to the SPEAKERS SURROUND BACK/BI-AMP/FRONT
54USTipTo enjoy better surround sound, the distance between the center speaker and the listening position B cannot be more than 5 feet closer than the
55US Amplifier OperationsTipSurround speaker position is designed specifically for implementation of the CINEMA STUDIO EX modes. For other sound fiel
56USSettings for the S-AIR (S. AIR menu)For details on S-AIR, see “S-AIR Operations” (page 80).Enjoying Dolby Digital and DTS Surround sound (AUTO FOR
57US Enjoying Surround SoundTypes of A.F.D. mode* You cannot select this decoding mode if the surround back speakers are set to “NO”.A.F.D. mode [Di
58USIf you connect a subwooferThis receiver will generate a low frequency signal for output to the subwoofer when there is no LFE signal, which is a l
59US Enjoying Surround SoundTypes of sound field available* You can only select this sound field if the headphones are connected to the receiver.Sou
6USS-AIR OperationsAbout S-AIR products...80Setting up an S-AIR product ...81Enjoying the system’s s
60USNotes• The effects provided by the virtual speakers may cause increased noise in the playback signal. • When listening with sound fields that empl
61US Enjoying Surround SoundListening to the sound without any adjustment (ANALOG DIRECT)You can switch the audio of the selected input to two chann
62USListening to FM/AM radioYou can listen to FM and AM broadcasts through the built-in tuner. Before operation, make sure you have connected the FM a
63US Tuner OperationsEnter the frequency of a station directly by using the numeric buttons.1 Press TUNER repeatedly to select the FM or AM band.Yo
64USPresetting FM/AM radio stationsYou can preset up to 30 FM stations and 30 AM stations. Then you can easily tune in the stations you often listen t
65US Tuner Operations1 Press TUNER repeatedly to select the FM or AM band.2 Press PRESET + or PRESET – repeatedly to select the preset station you
66USListening to Satellite RadioTo listen to Satellite Radio, you’ll need to connect a SIRIUS Satellite Radio tuner (sold separately) to your Sirius-R
67US Tuner OperationsConnecting the SIRIUS Satellite RadioConnect the SiriusConnect Home tuner. When you use the SiriusConnect Home tuner with this
68US7 Press b.The last 6 digits appear on the display.8 Check the SIRIUS ID on the display and write it in the space provided here.SIRIUS ID:_________
69US Tuner OperationsSelecting a channel of the SIRIUS Satellite RadioYou can select a channel from one category orall the categories by changing t
7USDescription and location of partsFront panel?/1PHONESSPEAKERSINPUT SELECTORINPUT MODE TUNING MODEMASTER VOLUMETONE MODE DISPLAY DIMMER MUTINGMEMORY
70US1 Press TUNER repeatedly to select “SIRIUS”.You can also use INPUT SELECTOR on the receiver.2 Press D.TUNING.3 Press the numeric buttons to enter
71US Tuner Operations3 Press MEMORY.You can also use MEMORY/ENTER on the receiver.4 Press the numeric buttons to select a preset number you want to
72USRestricting access to specific channels (Parental Lock) (SIRIUS only)You can restrict access to certain channels using your own lock code. The loc
73US Tuner Operations9 Reenter the new lock code with the numeric buttons.“CHANGED” appears on the display.To listen to the locked channels1Press T
74USSIRIUS Satellite Radio message list* “ANTENNA” and “ERROR” appears on the display alternately.** “CALL 888” and “539-SIRI” appears on the display
75US “BRAVIA” Sync FeaturesWhat is “BRAVIA” Sync?“BRAVIA” Sync is compatible with a Sony TV, Blu-ray Disc/DVD player, AV amplifier, etc., that is
76USPreparing for the “BRAVIA” SyncTo use the “BRAVIA” Sync, turn the Control for HDMI function on for both the receiver and the connected component.
77US “BRAVIA” Sync Features9 Set the Control for HDMI function for the connected component to on.If the Control for HDMI function for the connecte
78USEnjoying the TV sound from the speakers connected to the receiver (System Audio Control)You can enjoy the TV sound from the speakers connected to
79US “BRAVIA” Sync FeaturesTurning off the receiver with the TV (System Power Off)When you turn the TV off by using the POWER button on the TV’s
8USName FunctionK DISPLAY Press to select information displayed on the display (page 92).L 2CH/A.DIRECTPress to select a sound field (page 56, 58).A.F
80USAbout S-AIR productsThis receiver is compatible with the S-AIR function (page 98), which allows wireless sound transmission between S-AIR products
81US S-AIR OperationsSetting up an S-AIR productBefore using an S-AIR product, be sure to perform the following settings to establish the sound t
82USNotes• Insert the wireless transmitter with the S-AIR logo facing up.• Insert the wireless transmitter so that the V marks are aligned.• Do not in
83US S-AIR OperationsTo set the ID of the S-AIR sub unitBe sure to match the ID on S-AIR sub unit you want to the S-AIR main unit.For details on
84USx After pairingSound transmission is established between the paired S-AIR main unit and S-AIR sub unit(s) only.1 Place the S-AIR sub unit that you
85US S-AIR OperationsEnjoying the system’s sound in another room(For the S-AIR receiver only (not supplied))You can enjoy the system’s sound in a
86US8 Adjust the volume on the S-AIR receiver.NoteThe sound of the S-AIR receiver may be cut off by operation of the S-AIR main unit.Changing the chan
87US S-AIR Operations6 Press V/v repeatedly to select the setting you want.• RF AUTO: Normally select this. The system changes “RF SETUP” to “RF
88US5 Press or b to enter the parameter.6 Press V/v repeatedly to select the setting you want.• STBY OFF: You cannot enjoy the S-AIR receiver while
89US Other OperationsNotes• Some audio input modes may not be set up depending on the input.• When the ANALOG DIRECT function is being used, the
9USAbout the indicators on the displaySWLFESP ASP BLCSL SPL IIxOPT HDMI CATDTS -ES 96/24 MEMORYMONO SLEEP STD.RANGES-AIRCOAX NEO:6 SATSBSBLRSRSBRDEX1
90US8 Press V/v repeatedly to select the input (“SAT- DVD” in the example) you want to assign to the digital audio input jack selected in step 6.When
91US Other OperationsYou can listen to the sound and view the images from the component connected through the DIGITAL MEDIA PORT adapter to the
92US1 Press DMPORT.You can also use the INPUT SELECTOR on the receiver to select “DMPORT”.2 Start playback of the connected component.The sound is pla
93US Other OperationsUsing the Sleep TimerYou can set the receiver to turn off automatically at a specified time.Press SLEEP repeatedly while th
94US1 Press one of the input buttons to select the playback component.You can also use INPUT SELECTOR on the receiver.2 Prepare the playback component
95US Other OperationsTo set up speakers1 Press AMP MENU.“1-LEVEL” appears on the display.2 Press V/v repeatedly to select “7-SYSTEM”.3 Press or
96USChanging button assignmentsYou can change the factory settings of the input buttons to suit the components in your system. For example, if you con
97US Using the Remote/Additional InformationGlossaryx Cinema Studio EXA surround sound mode that can be regarded as the compilation of Digital
98USx Dolby Pro Logic IIxTechnology for 7.1 channel (or 6.1 channel) playback. Along with audio encoded in Dolby Digital Surround EX, 5.1 channel Dolb
99US Additional Informationx Sampling frequencyTo convert analog audio to digital, analog data should be quantified. This process is called sa
Kommentare zu diesen Handbüchern