Sony CDX-R3300 Bedienungsanleitung PDF herunterladen

3-261-846-11 (1)

Cautions

•This unit is designed for negative ground 12 V

DC operation only.

•Do not get the leads under a screw, or caught

in moving parts (e.g. seat railing).

•Before making connections, turn the car

ignition off to avoid short circuits.

•Connect the yellow and red power input leads

only after all other leads have been connected.

•Run all ground leads to a common ground

point.

•Be sure to insulate any loose unconnected

leads with electrical tape for safety.

•The use of optical instruments with this

product will increase eye hazard.

Notes on the power supply lead (yellow)

•When connecting this unit in combination with

other stereo components, the connected car

circuit’s rating must be higher than the sum of

each component’s fuse.

•When no car circuits are rated high enough,

connect the unit directly to the battery.

Parts Iist (1)

•The numbers in the list are keyed to those in

the instructions.

•The bracket 1 and the protection collar 3 are

attached to the unit before shipping. Before

mounting the unit, use the release keys 5 to

remove the bracket 1 and the protection collar

3 from the unit. For details, see “Removing

the protection collar and the bracket (4)” on

the reverse side of the sheet.

•Keep the release keys 5 for future use as

they are also necessary if you remove the

unit from your car.

Caution

Handle the bracket 1 carefully to avoid injuring

your fingers.

Note

Before installing, make sure that the catches on

both sides of the bracket 1 are bent inwards 2 mm

(

in). If the catches are straight or bent outwards,

the unit will not be installed securely and may spring

out.

Installation/Connections

Installation/Connexions

FM/AM

Compact Disc

Player

Connection example (2)

Notes (2-B)

• Be sure to connect the ground lead before

connecting the amplifier.

• If you connect an optional power amplifier and do

not use the built-in amplifier, the beep sound will

be deactivated.

Connection diagram (3)

1 To a metal surface of the car

First connect the black ground lead, then

connect the yellow and red power input leads.

2 To the power antenna control lead or power

supply lead of antenna booster amplifier

Notes

• It is not necessary to connect this lead if there

is no power antenna or antenna booster, or

with a manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control

and power supply leads.”

3 To AMP REMOTE IN of an optional power

amplifier

This connection is only for amplifiers. Connecting

any other system may damage the unit.

4 To the +12 V power terminal which is energized

in the accessory position of the ignition key

switch

Notes

• If there is no accessory position, connect to the

+12 V power (battery) terminal which is

energized at all times.

Be sure to connect the black ground lead to a

metal surface of the car first.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control

and power supply leads.”

5 To the +12 V power terminal which is energized

at all times

Be sure to connect the black ground lead to a

metal surface of the car first.

AUDIO OUT REAR

1 32

Equipment used in illustrations (not supplied)

Appareils utilisés dans les illustrations (non fournis)

Rear speaker

Haut-parleur arrière

Front speaker

Haut-parleur avant

Power amplifier

Amplificateur de puissance

× 2

Active subwoofer

Caisson de graves actif

CDX-R3300

CDX-R3000

Catch

× 4

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Compact Disc

Seite 2 - Attention

Précautions•Cet appareil est exclusivement conçu pourfonctionner sur une tension de 12 V CC avecmasse négative.•Évitez de fixer des vis sur les câbles

Seite 3 - OPEN/EJECT

OPEN/EJECT182 mm53 mm41 23311DashboardTableau de bord56 A TOYOTAto dashboard/center consolevers le tableau de bord/la console centraleBracketSupportBr

Seite 4

Precautions•Choose the installation location carefully sothat the unit will not interfere with normaldriving operations.•Avoid installing the unit in