Sony GDM-F520 Bedienungsanleitung PDF herunterladen (Seite 6)

Troubleshooting

x No picture

If the ! (power) indicator is not lit

• Check that the power cord is properly connected.

• Check that the ! (power) switch is in the “on” position.

The ! (power) indicator is orange

• Check that the video signal cable is properly connected and all plugs

are firmly seated in their sockets.

• Check that the INPUT switch setting is correct.

• Check that the HD15 video input connector’s pins are not bent or

pushed in.

• Check that the computer’s power is “on”.

• The computer is in power saving mode. Try pressing any key on the

computer keyboard or moving the mouse.

• Check that the graphic board is completely seated in the proper bus

slot.

If the ! (power) indicator is green or flashing orange

• Use the Self-diagnosis function.

x Picture flickers, bounces, oscillates, or is scrambled

• Isolate and eliminate any potential sources of electric or magnetic

fields such as other monitors, laser printers, electric fans, fluorescent

lighting, or televisions.

• Move the monitor away from power lines or place a magnetic shield

near the monitor.

• Try plugging the monitor into a different AC outlet, preferably on a

different circuit.

• Try turning the monitor 90° to the left or right.

• Check your graphics board manual for the proper monitor setting.

• Confirm that the graphics mode and the frequency of the input signal

are supported by this monitor (see “Preset mode timing table” on

page i). Even if the frequency is within the proper range, some

graphics board may have a sync pulse that is too narrow for the

monitor to sync correctly.

• Adjust the computer’s refresh rate (vertical frequency) to obtain the

best possible picture.

x Picture is fuzzy

• Adjust the contrast, brightness, and PICTURE EFFECT.

• Degauss the monitor.*

• Adjust the degree of moire cancellation until the moire is minimal,

or set CANCEL MOIRE to OFF.

x Picture is ghosting

• Eliminate the use of video cable extensions and/or video switch

boxes.

• Check that all plugs are firmly seated in their sockets.

x Picture is not centered or sized properly

• Perform the Auto Size Center function.

• Adjust the size or centering. Note that with some input signals and/

or graphics board the periphery of the screen is not fully utilized.

• Just after turning on the power switch, the size/center may take a

while to adjust properly.

x Edges of the image are curved

• Adjust the geometry.

x Wavy or elliptical pattern (moire) is visible

• Adjust the degree of moire cancellation until the moire is minimal.

• Change your desktop pattern.

x Color is not uniform

• Degauss the monitor.* If you place equipment that generates a

magnetic field, such as a speaker, near the monitor, or if you change

the direction the monitor faces, color may lose uniformity.

• Adjust the landing.

x White does not look white

• Adjust the color temperature.

• Check that the 5 BNC connectors are connected in the correct order.

x Monitor buttons do not operate ( appears on the

screen)

• If the control lock is set to ON, set it to OFF.

x Letters and lines show red or blue shadows at the

edges

• Adjust the convergence.

x USB peripherals do not function

• Check that the appropriate USB connectors are securely connected.

• Turn the monitor OFF and then ON again, then reconnect USB cable.

• If you connect a keyboard or mouse to the USB connectors and then

boot your computer for the first time, the peripheral devices may not

function. First connect the keyboard and mouse directly to the

computer and set up the USB compliant devices. Then connect them

to this monitor.

• Install the latest version of the device driver on your computer.

Contact your device’s manufacturer for information about the

appropriate device driver.

x A hum is heard right after the power is turned on

• This is the sound of the auto-degauss cycle. When the power is

turned on, the monitor is automatically degaussed for a few seconds.

* If a second degauss cycle is needed, allow a minimum interval of

20 minutes for the best result. A humming noise may be heard, but this is

not a malfunction.

On-screen messages

1 If “NO SIGNAL” appears:

This indicates that no signal is input from the selected connector.

2 Shows the currently selected connector.

3 Shows the remedies.

• If ACTIVATE BY COMPUTER appears on the screen, try

pressing any key on the computer or moving the mouse, and

confirm that your computer’s graphic board is completely seated

in the correct bus slot.

• If CHECK SIGNAL CABLE appears on the screen, check that

the monitor is correctly connected to the computer.

• If CHECK INPUT SELECTOR appears on the screen, try

changing the input signal.

1 If “OUT OF SCAN RANGE” appears:

This indicates that the input signal is not supported by the monitor’s

specifications.

2 Shows the input signal frequency.

3 Shows the remedies.

CHANGE SIGNAL TIMING appears on the screen. If you are

replacing an old monitor with this monitor, reconnect the old

monitor. Then adjust the computer’s graphic board so that the

horizontal frequency is between 30 – 137 kHz (GDM-F520),

30 – 115 kHz (GDM-F420), and the vertical frequency is between

48 – 170 Hz.

IIONNFORMAT

MON I I I NGS WORKTOR

IVATE

2:NO

COMPUTER

GNALI

S GNAL CABLEI

NPUT

I NPUT SELECTOR

ACT

CHECK

IIONNFORMAT

MON I I I NGS WORKTOR

I1:.200 0 /kHz 85Hz

RANGE

S GNAL TIIINGM

NPUT

OUT OF SCAN

CHANGE

1 2 3 4 5 6 7 8 9 10 11 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

Sony GDM-F520 Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Monitore Sony GDM-F520