Sony SRP-X700P Bedienungsanleitung

Digital Powered MixerSRP-X700PRS-232C Interface Manual1st EditionIssued: 7/2002 2002 Sony Sound Communications Inc.

– 10 –• ParameterThe parameters to be returned have the following meaning.byte Parameter nameSpecifiedValuebyte Parameter name1st MIC 1/WL 1 LEVEL MET

– 11 –Level meter valueThe level meter values [dB] are indicated as shown below.MIC SWITCHThis command is used to display the status of the +48V switc

– 12 –MIC INPUT –∞Turning on/off of the -∞ indicators of MIC1/WL1 to MIC6/LINE2 is indicated by the 8-bit data.bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

– 13 –CLIP/PROTECTIONTurning on/off of the CLIP and PROTECTION indicators of speaker output is indicated by the 8-bit data.bit7 bit6 bit5 bit4 bit3 bi

– 14 –PARALLEL OUTPUT7-10Presence or absence of output signal at the PARALLEL OUTPUT7 to 10 connectors on the rear panel of the SRP-X700P is indicated

– 15 –MIC MUTINGStatus of muting of MIC1/WL1 to MIC6/LINE2 is indicated by the 8-bit data.bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit00 1 MIC6/ MIC5/ MIC4

– 16 –GROUP MUTING Status of muting of REMOTE1 to 6 among the GROUP FADER is indicated by the 8-bit data.bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit00 1 RE

– 17 –LOCK/FADERStatus of the PANEL LOCK and that of FADER MODE are indicated by the 8-bit data.bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0010000PANEL LOC

– 18 –Parameter Setting CommandsThe following commands are the group of commands used to enable you the detailed setting of internal functions of the

– 19 –FIRMWARE VERSION REQUEST : 52[H] 56[H] 45[H] 52[H] ( ‘RVER’ )This command is used to read the version number of the SRP-X700P firmware.• Packet

– 2 –OverviewThis is the Interface Manual for the Sony SRP-X700P Digital Powered Mixer. This protocol is designed to control the SRP-X700P DigitalPowe

– 20 – GROUP FADER : 43[H] 47[H] 46[H] 41[H],42[H] (‘CGFA,B’)43[H] 47[H] 46[H] 31[H]-36[H] (‘CGF1-2’)This command is used to set any desired single ch

– 21 –• Index (2-9th byte)This command is used to specify index of the input channels with 8 bytes of the ASCII code.CautionIf number of index charact

– 22 –GROUP FADER PARAMETER REQUEST: 52[H] 47[H] 46[H] 41[H],42[H] (‘RGFA,B’)52[H] 47[H] 46[H] 31[H]-36[H] (‘RGF1-2’)This command is used to read the

– 23 –• INFORMATION (2-129th byte)Specify the index of the input channels using the ASCII code.CautionIf number of index characters does not reach the

– 24 –• TRIM (10th byte)This command is used to set the reference level of the input terminal.• Function ON/OFF (11th byte)This command is used to tur

– 25 –• PEQ Q (13 and 16th byte)This command is used to set the Q value of parametric equalizer.• PEQ gain (14 and 17th byte)This command is used to s

– 26 –• Fader level (19th byte)This command is used to set the fader level [dB].This fader levels are shown as the fader values on the INPUT OVERVIEW

– 27 –LINE 4 INPUT : 43[H] 49[H] 4D[H] 34[H] (‘CIL4’)This command is used to implement setting up the LINE 4 input channel.Various setups can be memor

– 28 –LINE OUTPUT1,2 : 43[H] 4F[H] 4C[H] 31[H],32[H] (‘COL1,2’)This command is used to implement setup of any desired single channel of the LINE OUTPU

– 29 –• REF LEVEL (10th byte)This command is used to set the reference output level [dBu].• Function ON/OFF (11th byte)This command is used to turn ON

– 3 –Communication ProtocolThe communication protocol is described below.• When the SRP-X700P has received a command from computer successfully, the S

– 30 –LINE OUTPUT 1,2 PARAMETER REQUEST :52[H] 4F[H] 4D[H] 31[H],32[H] (‘ROL1,2’)This command is used to read the setup of any desired single channel

– 31 –• ParameterThe parameter consists of the 26 bytes all the time in the order as shown in the table below.When you specify NONE (30[H] ‘0’) as the

– 32 –LINE OUTPUT3-8 PARAMETER REQUEST :52[H] 4F[H] 4D[H] 33[H]-38[H] (‘ROL3-8’)This command is used to read the setup of any desired single channel o

– 33 –• Packet format43[H] 49[H] 4D[H] 31[H] “parameter” 0D[H](In the case of MIC1/WL1 input channels)• ParameterThe parameter consists of the 41 byte

– 34 –• TRIM (10th byte)This command is used to set the reference level [dBu] of the input terminals.• Function ON/OFF (11th byte)This command is used

– 35 –MIC INPUT PARAMETER REQUEST : 52[H] 49[H] 4D[H] 31[H]-36[H] (‘RIM1-6’)This command is used to read the setup of any desired single channel of th

– 36 –When you specify the scene No.(31[H] (‘1’) through 44[H] (‘D’)), parameters of the subsequent 2nd through 8th bytes are written in thescene memo

– 37 –• MASTER MUTING (6th byte)This command is used to specify muting of the MASTER A and B with the 8-bit data.When you want to set the MUTING statu

– 38 –PANEL LOCK/FADER MODE : 43[H] 53[H] 45[H] 4C[H] ( ‘CSEL’ )This command is used to set the PANEL LOCK and the FADER MODE.• Packet format43[H] 53[

– 39 –• INPUT Function 1 (1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23rd byte)This command is used to set the PARALLEL INPUT function 1.• INPUT Function

– 4 –Command ReferenceBasic Control CommandsThe group of the Basic Control Commands contains 12 commands that enable you to perform the basic operatio

– 40 –• OUTPUT Function 1 (25, 27, 29, 31, 33, 35, 37, 39, 41, 43rd byte)This command is used to set the PARALLEL OUTPUT function 1.• OUTPUT Function

– 41 –PARALLEL I/O PARAMETER REQUEST : 52[H] 50[H] 49[H] 4F[H] ('RPIO')This command is used to read setup of the REMOTE PARALLEL terminal fr

– 42 –REC OUT PARAMETER REQUEST : 52[H] 4F[H] 4D[H] 33[H],32[H] (‘ROR1,2’)This command is used to read parameter of the desired single channel of the

– 43 –• LINE3-4F machine type (1, 3, 5, 7, 9, 11 and 13th byte)This command is used to set category of the Control S.• LINE3-4F connection (2, 4, 6

– 44 –• Projector protocol (23rd byte)This command is used to select protocol of the projector to be connected.Bit 0 of the “PJ CONTROL” changes depen

– 45 –ROUTING : 43[H] 52[H] 4C[H] 31[H]-38[H] (‘CRL1-8’)43[H] 52[H] 52[H] 31[H]-32[H] (‘CRR1-2’)This command is used to set the routing for the OUTPUT

– 46 –• Level (2-17th byte)This command is used to set the ASSIGN level [dB].• MIC1/WL1-MIC6/LINE2 ON/OFF (18th byte)This command is used to turn ON/O

– 47 –ROUTING PARAMETER REQUEST : 52[H] 52[H] 4C[H] 31[H]-38[H] (‘RRL1-8’)52[H] 52[H] 52[H] 31[H]-32[H] (‘RRR1-2’)This command is used to read setup o

– 48 –SCENE PARAMETER REQUEST : 52[H] 53[H] 43[H] 52[H] (‘RSTR’)This command is used to read the setups of the functions of recalling at the event of

– 49 –SCENE RECALL BUTTON : 43[H] 52[H] 53[H] 41[H] (‘CRSA’)This command is used to set the scene No. to be recalled, to the SCENE RECALL A to D butto

– 5 –REMOTE COMMANDStop sending 30[H] ( ‘0’ )PLAY 31[H] ( ‘1’ )PAUSE 32[H] ( ‘2’ )STOP 33[H] ( ‘3’ )F. F. 34[H] ( ‘4’ )REW. 35[H] ( ‘5’ )REC 36[H] ( ‘

– 50 –SCENE RECALL BUTTON PARAMETER REQUEST :52[H] 52[H] 53[H] 41[H] (‘RRSA’)This command is used to read the scene Nos. that are set to the SCENE REC

– 51 –• Scene No. (1st byte)This command is used to specify the scene No. to be stored.• Function 1, 2 (10, 11th byte)This command is used to specify

– 52 –SPEAKER OUTPUT : 43[H] 4F[H] 53[H] 50[H] (‘COSP’)This command is used to set the SPEAKER OUTPUT.Various setups can be memorized in the scene mem

– 53 –ATT LEVEL ATT LEVEL ATT LEVEL30[H] (‘0‘)18 42[H] (‘B’)8 4C[H] (‘L’)30 39[H] (‘9‘)17 43[H] (‘C’) 7 4D[H] (‘M’)27 3A[H] (‘:‘)16 44[H] (‘D’)6 4E[H]

– 54 –Sony CorporationPrinted in Japan9-870-518-11

– 6 –LEVEL UP: 43[H] 4C[H] 56[H] 2B[H] (‘CLV+’)This command is used to increase the sound volume of the specified channel.When this command is sent,

– 7 –MUTING: 43[H] 4D[H] 55[H] 54[H] (‘CMUT’)This command is used to mute the specified channel or cancel muting of the specified channel.• Packet fo

– 8 –PARALLEL OUTPUT ON: 43[H] 50[H] 4F[H] 4E[H] (‘CPON’)This command is used to turn on OUTPUT of the REMOTE PARALLEL terminals separately of the SRP

– 9 – SCENE RECALL: 43[H] 52[H] 43[H] 4C[H] (‘CRCL’)This command is used to recall the desired scene.• Packet format43[H] 52[H] 43[H] 4C[H] “paramete