Sony XSP-N1BT Betriebsanleitung PDF herunterladen (Seite 19)

19GB

RB ENH (rear bass enhancer)

Rear Bass Enhancer enhances the bass sound by

applying a low pass filter setting to the rear

speakers. This function allows the rear speakers

to work as a subwoofer if one is not connected.

(Available only when [SW DIREC] is set to [OFF].)

RBE MODE (rear bass enhancer mode)

Selects the rear bass enhancer mode: [1], [2], [3],

[OFF].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

SW DIREC (subwoofer direct connection)

You can use the subwoofer without a power

amplifier when it is connected to the rear

speaker cord. (Available only when [RBE MODE]

is set to [OFF].)

Be sure to connect a 4 - 8 ohm subwoofer to

either of the rear speaker cords. Do not connect

a speaker to the other rear speaker cord.

SW MODE (subwoofer mode)

Selects the subwoofer mode: [1], [2], [3], [OFF].

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORM], [REV].

SW POS* (subwoofer position)

Selects the subwoofer position: [NEAR],

[NORMAL], [FAR].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

S.WOOFER (subwoofer)

SW LEVEL (subwoofer level)

Adjusts the subwoofer volume level:

[+10 dB] – [0 dB] – [-10 dB].

([ATT] is displayed at the lowest setting.)

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORM], [REV].

SW POS* (subwoofer position)

Selects the subwoofer position: [NEAR],

[NORMAL], [FAR].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF SLOP (low pass filter slope)

Selects the LPF slope: [1], [2], [3].

HPF (high pass filter)

HPF FREQ (high pass filter frequency)

Selects the front/rear speaker cut-off frequency:

[OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].

HPF SLOP (high pass filter slope)

Selects the HPF slope (effective only when [HPF

FREQ] is set to other than [OFF]): [1], [2], [3].

BTA VOL (BLUETOOTH audio volume level)

Adjusts the volume level for each connected

BLUETOOTH device: [+6 dB] – [0 dB] – [-6 dB].

This setting negates the need to adjust the

volume level between sources.

* Does not appear when [SET F/R POS] is set to [OFF].

DISPLAY Setup

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

DIMMER

Changes the display brightness [ON], [OFF].

ILLUM (Illumination)

Changes the illumination color: [1], [2].

AUTO SCR (auto scroll)

Scrolls long items automatically: [ON], [OFF].

BT (BLUETOOTH) Setup

PAIRING (page 7)

PHONEBOOK (page 14)

REDIAL (page 15)

RECENT CALL (page 14)

VOICE DIAL (page 15)

DIAL NUMBER (page 15)

RINGTONE

Selects whether this unit or the connected

cellular phone outputs the ringtone: [1] (this

unit), [2] (cellular phone).

AUTO ANS (auto answer)

Sets this unit to answer an incoming call

automatically: [OFF], [1] (about 3 seconds), [2]

(about 10 seconds).

AUTO PAIRING

Start BLUETOOTH pairing automatically when

iOS device version 5.0 or later is connected via

USB: [ON], [OFF].

BT SIGNL (BLUETOOTH signal) (page 8)

Activates the BLUETOOTH function: [ON], [OFF].

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 95 96

Kommentare zu diesen Handbüchern

Keine Kommentare