Sony DTC-57ES Bedienungsanleitung PDF herunterladen (Seite 20)

Recording

1 Make sure that the TIMER switch is set to the OFF

position, and turn on the power.

2 Insert a cassette and press the ^OPEN/CLOSE button

to load the cassette. (See page 18.)

Then locate the position at which you want to start

recording.

To start recording from the beginning of the tape, press

the button. (Press the button again, the TOP'

indicator will appear at the beginning of the tape.)

To start from the middle of the tape, locate the point

immediately before the blank section with the end search

function. (See page 23).

3 Set the INPUT selector to ANALOG, OPUCAL or

COAXIAL depending upon your sound source.

4 Press the «REC button.

IRECI. ► and II indicators light on the display, and the

deck enters the record-pause mode. The sampling

frequency to be applied for recording appears.

If the digital copy prohibit signal is written on the

codes of the sound source, the COPY PROHIBIT

indicator appears in the display window and signifies

that you cannot record that source with the digital-to-

digital connection. In this case, use the analog-to-

analog connection.

5 When recording the analog input signal, adjust

the recording level and balance with the REC LEVEL

and BALANCE controls respectively. (See page 22.)

No recording level adjustment is required when recording

the digital input signal.

0 To record in the long-play mode, set the REC MODE

selector to the LONG position. (See page 22.)

7 Press the iiPAUSE or ► (play) button.

The II indicator goes off. and recording starts.

To write start ID automatically during recording

Make sure that the AUTO indicator is lit.

If not, press the START ID AUTO button. (See page 27.)

To designate the program number

Press the desired numeric button. (See page 29.)

When recording from the beginning of the tape, the

program number will be assigned automatically from 1.

To insert sound muted portion at the beginning of the

tape

Do not advance the tape with the ►► or ► button. This will

leave a blank section at the beginning. Be sure to proceed

with the record muting function. (See page 23.)

To stop recording

Press the ■ button.

To stop recording for a moment

Press the iiPAUSE button.

When you press the FADER or OREC MUTE button, the

deck will also enter the record-pause mode.

To release pause and restart recording

Press the IiPAUSE or ► button.

To remove the cassette

Press the ^OPEN/CLOSE button.

if recording cannot be made

Check the following;

e The safety tab of the cassette is set to the record-inhibit

position. (See page 18.)

e No cassette is loaded.

e The INPUT selector is set to the incorrect position,

e Tape is fully rewound to the end.

e The output level of the playback equipment is too low.

• The digital copy prohibit signal is written in the codes of the

sound source you want to record. (The COPY PROHIBIT

indicator appears in the display window.)

• The REC LEVEL control is set to the 0 position. (Only when

recording the analog input signal.)

Note on the INPUT selector and the REC MODE selector

Do not change the position of these selectors after

recording starts.

if the cassette is ejected after it has been loaded

Check to see if the cassette is inserted correctly. (See page

18.)

When the tape is recorded to the end (Auto rewind

function)

The tape is rewound to the beginning and stops

automatically.

The auto rewind function is not applied when the TIMER

switch is set to the REC position.

Accuracy of the electronic linear time counter

The linear time counter provided with this unit is not a clock.

The time indicated by the counter may differ slightly from

the actual recording/playback time.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 48 49

Kommentare zu diesen Handbüchern

Keine Kommentare

Sony DTC-57ES Bedienungsanleitung Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Diktiergeräte Sony DTC-57ES