Sony CMT-S40D Bedienungsanleitung PDF herunterladen

2 3 4

6 7 85

10 11 129

14 15 1613

Continued



WARNING

To reduce the risk of fire, do not

cover the ventilation opening of

the appliance with newspapers,

tablecloths, curtains, etc.

Do not expose the appliance to naked

flame sources (for example, lighted

candles).

To reduce the risk of fire or electric

shock, do not expose this appliance

to dripping or splashing, and do not

place objects filled with liquids, such as

vases, on the appliance.

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet.

As the main plug is used to disconnect

the unit from the mains, connect the

unit to an easily accessible AC outlet.

Should you notice an abnormality in

the unit, disconnect the main plug from

the AC outlet immediately.

Do not expose batteries or appliances

with battery-installed to excessive heat,

such as sunshine and fire.

The unit is not disconnected from the

mains as long as it is connected to the

AC outlet, even if the unit itself has

been turned off.

CAUTION

The use of optical instruments with this

product will increase eye hazard.

This appliance is classified as a CLASS 1

LASER product. This marking is located

on the rear exterior.

Notice for customers: the following

information is only applicable to

equipment sold in countries applying

EU directives.

This product has been manufactured

by or on behalf of Sony Corporation,

1-7-1 Konan Minato-ku Tokyo, 108-0075

Japan. Inquiries related to product

compliance based on European Union

legislation shall be addressed to

the authorized representative, Sony

Deutschland GmbH, Hedelfinger

Strasse 61, 70327 Stuttgart, Germany.

For any service or guarantee matters,

please refer to the addresses provided

in the separate service or guarantee

documents.

To ensure that the battery will be

treated properly, hand over the

product at end-of-life to the applicable

collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view

the section on how to remove the

battery from the product safely. Hand

the battery over to the applicable

collection point for the recycling of

waste batteries.

For more detailed information about

recycling of this product or battery,

please contact your local Civic Office,

your household waste disposal service

or the shop where you purchased the

product.

About this manual



“DVD” may be used as a general term

for a DVD VIDEO, DVD-R, DVD-RW,

DVD+R or DVD+RW.



CD-R or CD-RW is sometimes referred

to as “DATA CD.”



DVD-R, DVD-RW, DVD+R or DVD+RW

is sometimes referred to as “DATA

DVD.”



This manual mainly explains

operations using the remote, but the

same operations can also be

performed using the buttons on the

unit having the same or similar

names.

Disposal of Old Electrical

& Electronic Equipment

(Applicable in the

European Union and

other European countries

with separate collection

systems)

This symbol on the product or on its

packaging indicates that this product

shall not be treated as household

waste. Instead it shall be handed over

to the applicable collection point

for the recycling of electrical and

electronic equipment. By ensuring this

product is disposed of correctly, you

will help prevent potential negative

consequences for the environment and

human health, which could otherwise

be caused by inappropriate waste

handling of this product. The recycling

of materials will help to conserve

natural resources.

For more detailed information about

recycling of this product, please

contact your local Civic Office, your

household waste disposal service or

the shop where you purchased the

product.

Applicable accessories: Remote

commander

Europe Only

Disposal of waste

batteries (applicable in

the European Union

and other European

countries with separate

collection systems)

This symbol on the battery or on the

packaging indicates that the battery

provided with this product shall not be

treated as household waste.

On certain batteries this symbol

might be used in combination with

a chemical symbol. The chemical

symbols for mercury (Hg) or lead (Pb)

are added if the battery contains more

than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are

disposed of correctly, you will

help prevent potentially negative

consequences for the environment and

human health which could otherwise

be caused by inappropriate waste

handling of the battery. The recycling

of the materials will help to conserve

natural resources.

In case of products that for safety,

performance or data integrity reasons

require a permanent connection with

an incorporated battery, this battery

should be replaced by qualified service

staff only.

Playable Discs

DVD DVD VIDEO

DVD-ROM

DVD-R*/DVD-RW*

DVD+R*/DVD+RW*

CD-DA (Music CD)

CD-ROM

CD-R*/CD-RW*

VIDEO CD

* If discs have not been correctly

finalized, they will not be played

back. For more information, refer to

the operating instructions supplied

with the recording device.

Discs that cannot be played



Blu-ray discs



HD DVDs



DVD-RAMs



DVD Audio discs



PHOTO CDs



Super Audio CDs



Data track of CD-Extras



Audio material side of DualDiscs



DVD-R/DVD-RW/DVD+R/DVD+RW in

VR (Video Recording) mode



CPRM (Content Protection for

Recordable Media)-compatible

DVD-R/RW containing content

flagged as “Copy once.”

Music discs encoded with copyright

protection technologies

This product is designed to play back

discs that conform to the Compact Disc

(CD) standard. Recently, various music

discs encoded with copyright

protection technologies are marketed

by some record companies. Please be

aware that among those discs, there

are some that do not conform to the

CD standard and may not be playable

by this product.

Note on DualDiscs

A DualDisc is a two sided disc product

which mates DVD recorded material on

one side with digital audio material on

the other side. However, since the

audio material side does not conform

to the Compact Disc (CD) standard,

playback on this product is not

guaranteed.

Note on playback operations of a

DVD

Some playback operations for a DVD

may be intentionally restricted by

software producers. Since this system

plays a DVD according to the disc

contents, some playback features may

not be available.

Note about double-layer DVDs

The playback picture and sound may

be momentarily interrupted when the

layers switch.

Region code (DVD VIDEO only)

Your system has a region code printed

on the rear of the unit and will only

play a DVD VIDEO (playback only)

labeled with an identical region code or

Note on multi-session discs

This system can play back continuous

sessions on a disc when they are

recorded in the same format as the first

session. When a session recorded in a

different format is encountered, that

session and the ones following it

cannot be played back. Note that even

if the sessions are recorded in the same

format, some sessions may not play

back.

Notes on discs



The system can only play back a

standard circular disc. Using anything

other than standard or circular discs

(e.g., card, heart, or star shaped discs)

may cause a malfunction.



Do not use a disc that has a

commercially available accessory

attached, such as a label or ring.

Playable File Types

Video

File format Extensions

Xvid video “.avi”

Music

File format Extensions

MP3 (MPEG1 Audio

Layer 3)

“.mp3”

WMA

“.wma”

Photo

File format Extensions

JPEG “.jpg” or “.jpeg”

MP3 PRO format is not supported.

WMA DRM, WMA Lossless and WMA

PRO formats are not supported.

Notes



Some files may not play depending

on the format, the encoding method

or the recording condition.



Some USB devices may not work with

this system.



Do not connect the system and the

USB device through a USB hub.



The system supports ISO 9660 Level

1/Level 2 for DATA CD.



The system supports UDF (Universal

Disk Format) for DATA DVD.



The system supports FAT16 and FAT32

for USB devices.



The system can recognize files or

folders on a DATA DVD, DATA CD or

USB device as follows:

ˋ up to 188 folders including the root

folder on a DATA DVD, DATA CD or

USB device

ˋ up to 999 files on a DATA DVD,

DATA CD or USB device



It may take time to read files in the

following cases:

ˋ there are too many folders or files

on a DATA DVD, DATA CD or USB

device.

ˋ the memory capacity of the USB

device is very large.

ˋ the memory of the USB device is

fragmented.

Compatible USB Devices with

This System

Check the websites below for

information about compatible USB

devices.

For customers in Europe:

http://support.sony-europe.com/

For customers in Latin America:

http://esupport.sony.com/LA

For customers in other countries/

regions:

http://www.sony-asia.com/support

Preparing the Remote

Insert an R6 (size AA) battery (not

supplied), matching the polarities as

shown below.

Notes on using the remote



With normal use, the battery should

last for about six months.



If you do not use the remote for a

long period of time, remove the

battery to avoid damage from battery

leakage and corrosion.

Hooking Up the System Securely

FM lead antenna

(Extended horizontally.)

To right speaker

To left speaker

Speaker cord (Red/)

Speaker cord (Black/)

To wall outlet

 Antenna

Find a location and orientation that

provide good reception when you set

up the antenna.

Keep the antenna away from the

speaker cords and the power cord to

avoid picking up noise.

 AUDIO IN and VIDEO OUT jacks

AUDIO IN:

Connect an external audio component.

VIDEO OUT:

Connect the video input jack of the TV

or projector.

Attaching the Speaker Pads

Attach the supplied speaker pads at

each corner on the bottom of the

speakers to prevent them from

slipping.

Setting the Clock

1 Press /



to turn on the

system.

2 Press and hold SHIFT



, then

press ANGLE/TIMER MENU



select the clock set mode.

If “SELECT” appears on the display,

press /



repeatedly to

select “CLOCK,” and then press

(enter)



3 Press /



to set the hour,

and then press



4 Use the same procedure to set the

minutes.

The clock settings are lost when

you disconnect the power cord or if

a power failure occurs.

To display the clock

Ą When the system is off

Press TIME



. The clock is displayed

for about 8 seconds.

Ą When the system is on

Press TIME



. The clock is displayed

for about 8 seconds.

Connecting Your TV

Connect the video input jack of your TV

to the VIDEO OUT jack on the unit,

using the supplied video cord.

When connecting a video deck

Connect the TV and the video deck

using video and audio cords (not

supplied) as shown below.

Video deck Unit

Do not connect directly.

If you connect a video deck between

this system and the TV, you may

experience video leakage when

watching the video signal from this

system. Do not connect a video deck

between this system and TV.

Setting Up the Color System

Change the color system if necessary

from [PAL], [NTSC] or [Auto] after

connecting your TV. The factory default

for the color system is [PAL] for

European, Russian, Saudi Arabian and

Argentine models, and [NTSC] for other

models. Note that the color system

setup function is not available for Latin

American models (except for Argentine

model).

1 Connect the power cord to a wall

outlet.

2 Press /



to turn on the

system.

3 Press FUNCTION



repeatedly to

switch the function to DVD/CD.

Playback starts automatically if a

disc with an auto playback function

is loaded. Press Ą



twice to stop

playback.

4 Press SETUP



in stop mode.

The setup menu appears.

5 Press /



repeatedly to select

[SCREEN] settings, then press



6 Press /



repeatedly to select

[TV System], then press



7 Press /



repeatedly to select

[PAL], [NTSC] or [Auto], then press



8 Press SETUP



to turn off the

setup menu.

Note

The display on the TV screen may be

interrupted momentarily after

changing the color system.

Parts and Controls

Main unit

Remote

/ (on/standby) button

Press to turn the system on or off.

Remote sensor

FUNCTION button

Press to select a function.

Unit:  (play/pause) button

Remote:  (play) button, 

(pause) button

Press to start or pause playback. To

return to playback from pause

status, press  (or  on the

unit).

Unit: Ą (stop)/CANCEL button

Remote: Ą (stop) button

ˋ Press once to stop playback and

remember the stop point

(resume point). Press  (or 

on the unit) after this to resume

playback from the point where

you stopped. If you want to start

playback from the first track/

title/chapter, etc., press Ą (or Ą/

CANCEL on the unit) twice, and

then press  (or  on the

unit).

ˋ Press to cancel automatic tuning

while scanning radio

frequencies.

EQ button

Press to select a sound effect.

Unit: TUNE +/ˋ button

Remote: TUNING +/ˋ button

Press to tune to a desired station.

Unit: / (previous/next)

button

Remote: / (previous/

next) button

Press to select a track, file or

chapter.

/ (fast reverse/ fast

forward) button

Press to find a point in a track, file

or chapter.

Unit: / button

Remote: /// button

Press to move the cursor for item

selection.

 (slow forward) button

Press in pause mode to watch in

slow-motion.

PRESET +/ˋ button

Press to select a preset radio

station.

 (open/close) button

Press to open or close the disc tray.

Unit: ENTER button

Remote:

(enter) button

Press to enter/confirm the

settings.

Unit: VOLUME control

Turn to adjust the volume.

Remote: VOLUME +/ˋ button

Press to adjust the volume.

MIC (microphone) jack

Use to connect a microphone.

 (USB) port

Use to connect a USB device. When

the connected device has a

rechargeable battery and the

system is turned on, the battery

will be charged by the system.

ECHO button

Press to adjust the echo level.

MIC LEVEL button

Press to adjust the microphone

volume.

TIME button

Press to display or switch the time

information during playback.

DIMMER button

Press to change the brightness of

the display of the unit. Repeatedly

pressing the button changes the

brightness in 2 levels (bright/dark).

ANGLE/TIMER MENU button

ˋ Press to switch to other viewing

camera angles when multi-

angles are recorded on a DVD

VIDEO.

ˋ Press to set the play timer. See

also the description for the SHIFT



button.

 DVD MENU button

ˋ Press to open or close the DVD

menu during playback of a DVD

VIDEO.

ˋ Press to return to the previous

screen while operating in the

folder/file list displayed on the

TV screen.

MUTING button

Press to mute or unmute the

sound.

 DISPLAY button

Press to display or hide the

pull-down menu for search mode

or for information about the

current playback.

SHIFT button

Press and hold to use with the

pink-labeled buttons (number

buttons, SLEEP



and TIMER



SETUP button

Press to open or close the setup

menu.

DVD TOP MENU button

ˋ Press to open the DVD top menu

when playing a DVD.

ˋ Press to turn the PBC function on

or off when playing a VIDEO CD

with PBC function.

AUDIO/SLEEP button

ˋ Press to select an audio signal

format during playback if

multiple audio signal formats are

available.

ˋ Press to select the FM reception

mode (monaural or stereo) when

listening to FM stereo programs.

ˋ Press to set the sleep timer. See

also the description for the SHIFT



button.

SUBTITLE button

Press to select a subtitle language

when multilingual subtitles are

available (e.g., DVD VIDEOs).

ZOOM button

Press to zoom in or zoom out of a

displayed picture when viewing a

DVD VIDEO, a VIDEO CD, an Xvid

video or a JPEG image. You can

scroll the picture up, down, left or

right at the selected magnification

level by pressing ///



PROGRAM button

Press to program CD-DA tracks for

program play, or press to preset

radio stations.

REPEAT button

Press to activate repeat playback

mode.

BASS BOOST button

Press to create a more dynamic

sound. You can turn the effect on

or off by pressing repeatedly.

TV INPUT button

Press to switch the TV’s input

source between the TV signal and

an other input source.

Note that only Sony TVs can be

operated using this remote.

TV / (on/standby) button

Press to turn the TV on or off.

Note that only Sony TVs can be

operated using this remote.

Playing a Disc

1 Press FUNCTION



repeatedly to

select the DVD/CD function.

2 Press 



on the unit to open the

disc tray.

3 Place a disc in the disc tray, then

press 



on the unit to close the

disc tray.

Playback starts automatically when

you close the disc tray.

If playback does not start

automatically, press 



With the label side up.

4 Press VOLUME +/ˋ



to adjust

the volume.

Playing Files on a Disc/USB

Device

1 Press FUNCTION



repeatedly to

select the DVD/CD or USB

function.



DVD/CD: For playback of files on a

disc.



USB: For playback of files on a

USB device.

2 Load the source.

Ą For a disc

Open the disc tray, place a disc in

the tray and then close it.

Ą For a USB device

Connect a USB device to the

(USB) port



USB device

3 Press /



repeatedly to select

a media type (music/photo/

video), then press



4 Press VOLUME +/ˋ



to adjust

the volume.

When you want to play a different

file, stop playback, and then follow

the procedure below.

To play a desired file

1 Press /



to move the cursor

, then press



2 Press /



to move the cursor

to a folder that contains a file you

want to play, then press



3 Press /



to move the cursor

to the desired file, then press



(or 



) to start playback.

(Example: MP3 disc)

4 Press VOLUME +/ˋ



to adjust

the volume.

To play a desired folder

1 Press /



to move the cursor

, then press



2 Press /



to move the cursor

to a desired folder, then press



(or 



Playback starts from the first file in

the selected folder, and playback

continues until playback of all files

within the folder ends.

3 Press VOLUME +/ˋ



to adjust

the volume.

Tips



You can select a file to play by

pressing /



repeatedly

during playback while watching

information on the display.



You can return to the previous screen

by pressing  DVD MENU



when

operating in the folder/file list

displayed on the TV screen.



You can move one page forward or

backward by pressing /



in the

folder/file list when multiple pages

exist for item selection.

 Speakers

Connect the speaker cords.

 Power

Connect the power cord to a wall

outlet.

Home Audio System

Operating Instructions

4-460-926-11(2)

CMT-S40D

1 2

Home Audio System 1

Inhaltsverzeichnis

Seite 1 - Home Audio System

2 3 46 7 8510 11 12914 15 1613Continued WARNINGTo reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers, tab

Seite 2

22 23 242118 19 201726 27 282530 31 3229Listening to Sound from an Optional ComponentYou can listen to sound from a component connected to the AUDIO I